Adinath Controls Private Limited

From the day of commencement, we are engaged in manufacturing, supplying, trading and exporting Thyristor Power Controller. A thyristor is a semiconductor device which acts as a switch, which passes current in one direction, when it is switched on and to switch on the alternative current, two devices should be connected in inverse parallel. To meet the variegated demands of customers, these controllers are available in different specifications as per the needs and requirements of customers. The Thyristor Power Controller offered by us is available at market leading prices.

Other details:

• Thyristor units start at 3A

• Sizes up to 2600A and 690Vac

Products Variety:

• Three Phase (2PH) 2-leg:

Single Phase Thyristor Power Controllers:

• A range of thyristor power controllers to switch single phase loads.

• Ideally suited for normal or variable resistive loads and transformer & inductive load types

• Each device is turned on at the appropiate time by a trigger pulse applied to the gate

• The device will remain on until the instantaneous load current through it drops to zero

• The trigger pulses are generated by a driver, which times the pulse

• Ensures the thyristor unit output is a function of the input demand signal firing mode

The Basic Firing Modes:

Zero Crossing (ZC):

• Used with the logic output from a temperature controller

• The cycle time is determined by the temperature controller

• ZC minimizes interference due to the fact that the thyristor unit switches ON and OFF at zero volts

Burst Firing (BF):

• This firing is performed digitally within the thyristor unit at zero volts, producing no EMC interference

• Analogue input is necessary for BF and the number of complete cycles must be specified for 50% power demand

• This value can be between 1 and 255 complete cycles, determining the speed of firing

• When 1 is specified, the firing mode becomes Single Cycle (SC)

Single Cycle (SC):

• SC is the fastest zero crossing switching method

• At 50% input signal, one cycle is ON and one cycle is OFF

• At 75%, 3 cycles are ON and one cycle is OFF

• If power demand is 76% the unit performs the same as for 75% but every time the unit switches ON the microprocessor divides 76/75 and memorizes the ratio

• When the sum is one the unit delivers one cycle more to the load

• With this firing it is necessary to have an analogue input

• SC is ideal for simple resistance loads

• Thermal mass of the load is small or as a low noise alternative to PA firing with some applications

We take pride in introducing ourselves as one of the renowned suppliers of SCR Power Controller that are fabricated using high grade raw material. These are engineered following well defined industrial procedures and are appreciated for their robust construction and excellent finish standards. They are available at competitive prices.

Technical Specifications:

• Single pole, Normally open switching device for control of resistive heating loads
• zero voltage or phase angle fired
• Extends Heater life-eliminates thermal shocks
• Convection cooled
• Supply voltage-120/240/440.Vac, 50-60 Hz, single, two or three phase for star/delta connected resistive load up to 15Amps to 200Amps
• I2T fuse protection options
• Soft start, voltage limit and manual pot available

We have in offer precision engineered Low Cost PID Temperature Controller that has dust and splash proof front panel, which is equivalent to IP66 / NEMA4X. These are engineered from the best quality raw material and are acknowledged for their sturdy construction and durable service life.

Technical Specifications:

• CE approved
• Auto tune pid
• Outputs relay, 4-20mA, 0-10Vdc, SSR Drive
• Sizes- 48 x 48 mm., 48 x 96 mm., 96 x 96 mm.
• Dual outputs with dual alarms
• Multi inputs (T/C: J,K,R,S,T,B,E,N; RTD: Pt100/JPt100; mV, volt, current
• Accuracy ±0.2% of FS ON/OFF temperature controller/ indicator
• Accepts thermocouple (J,K,R,S), RTD(Pt100) & linear
• Options RS232/RS485 communication, process variable retransmission, remote analog set point, transducer excitation

• Trouble-free functionality
• Easy to use
• Low maintenance

ADINATH CONTROLS PVT. LTD. is the market leader in the domain of manufacturing Process Control Equipment Since 1989. We are located in Gujarat and serving the market of USA and Canada. The guidance from CEO Mr. Jignesh Mori and experience of two decades has led us to the acme of Success. Our customer centric approach and consistency in delivering quality products is the key force of our achievements. Our range id known for various features such as durability, low maintenance, high efficiency and enhanced output. Our organization is undertaking  total solution for temperature, power control & related accessories such as sensors and SCR controllers, since 1989. We are also engaged in the field Manufacturing and Marketing of SCR Power Controllers & Temperature sensors. Consolidating on our advanced manufacturing facility and sophisticated machinery, we fabricate highly precision based senors and indicators which are very sensitive in nature. Owing to their high sensitivity these are capable of measuring any change in the environmental conditions. Thus, these are used across varied range of application such as in robotics, security systems, surveillance systems, defense and automation industry.

Under the constant guidance of our mentor, Nitin Desai MSEE, USA, we have been able to set bench marks for our competitors to follow. Owing his extensive business experience and ethical practices in various business dealings, we have one of the reputed organization in this industry.